| Customization: | Available |
|---|---|
| Membrane Type: | Hollow |
| Type: | UF |
|
Still deciding? Get samples of US$ 185/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Product Name: UF160 100K Dalton 0.01um Filtration PVC Hollow Fiber UF Membrane Module UF Filter Drinking Water maker
Features
High filtration accuracy, good effluent quality (turbidity less than 0.1NTU)
Strong hydrophilicity (contact angle as low as 47 °, less prone to fouling and flux recovery)
Membrane silk has high strength and good toughness (membrane silk elongation exceeds 50%)
Low pressure and high flux (can meet the design flux at a very low transmembrane pressure difference)
Good chemical stability (the performance of the membrane module remains unchanged after 20 acid and alkali chemical cleaning)
Strong anti pollution ability (cleaning cycle extended by 30% compared to peers, and membrane flux recovery effect is good)
| Film detail | ||||
| Type | Hollow fiber | |||
| Film making process | NIPS(wet process) | |||
| Membrane material | PVC | |||
| nominal bore | 0.01um | |||
| Membrane inner/outer diameter | 1/1.7mm | |||
| Component specifications | ||||
| Housing material | U-PVC | |||
| Pouring materials | epoxy resin | |||
| Connection port | DN32 | |||
| Effective membrane area | 17 squre meters | |||
| Full water weight | 30KG | |||
| Transport weight | 20KG | |||
| Package size | 148X28X29CM | |||
| Application and operating parameters | |||||
| Pre-filter | 50-150um | ||||
| Operation mode | Internal pressure operation | ||||
| molecular cut off | 100000 Daltons | ||||
| Operation pressure | 0.02~0.2MPa | ||||
| Max inlet pressure | 0.3MPa | ||||
| Maximum transmembrane pressure difference |
0.2MPa | ||||
| Continuous operation pH range | 2~12 | ||||
| Continuous residual chlorine concentration tolerable | 100PPM | ||||
| Intermittent residual chlorine concentration is tolerable | 200PPM | ||||
| operating temperature range | 1ºC~40ºC | ||||
| Influent turbidity | ≤15NTU | ||||
| Component design flux | 700-2000LPH | ||||
| Turbidity of produced water | <0.1NTU | ||||
| Water pollution density index (SDI15) | <1 | ||||
| Removing Escherichia coli | 99.99% remove | ||||
| Backwash frequency | 15-60minute/time | ||||
| Backwash pressure | ≤0.2MPa | ||||
| Backwash flow rate | 100~150L/H.m² | ||||
| Backwash dosing agent | 15-20PPM sodium hypochlorite | ||||
| Backwash dosing frequency | Suggest automatic dosing for each backwash | ||||
| Chemical cleaning frequency | Once every 1-4 months | ||||
| Pickling agent | Citric acid, oxalic acid, or hydrochloric acid (mixed into a solution with pH=2) | ||||
| Alkali washing agent | NaOH+NaClO(Prepared into a solution with pH=12) | ||||
High filtration accuracy, good effluent quality (turbidity less than 0.1NTU)
Strong hydrophilicity (contact angle as low as 47 °, less prone to fouling and flux recovery)
Membrane silk has high strength and good toughness (membrane silk elongation exceeds 50%)
Low pressure and high flux (can meet the design flux at a very low transmembrane pressure difference)
Good chemical stability (the performance of the membrane module remains unchanged after 50 acid and alkali chemical cleaning)
Strong anti pollution ability (cleaning cycle extended by 30% compared to peers, and membrane flux recovery effect is good)
Externally pressurized use, with strong pollution capacity and wider inlet water quality
){kind=link}